DIN EN 10025-5 S355J2WP Non- Alloy Structural Steel Plate TJC Steel can supply DIN EN 10025-5 S355J2WP Structural Carbon Steel Plate, mainly used in construction in the fields requiring carbon steel plates with kinds of impact tests and strength.
The steel shows a by 15% higher resistance to mineral wear due to sliding action in comparison to S235J2G3. For this steel are available (mat. No 1.0569 acc. to DIN EN 10025) grades for:- folding (KQ)-S355J2G3C - cold forming of sections (KP)-S355J2G3C - EN 10025-1 - Hot Rolled Products of Structural Steel EN 10025-1 - Hot Rolled Products of Structural Steel. These standard are the latest European standards for structural steel. hey replace BS 4360, EN 10025:1993, EN 10113:1993, EN 10155:1993 EN 10137:1996. Steel Names according to EN 10027-1 in form of .X(1) nnn(2) Xn (3) Xn(4)..Example S355J2G3
EN 10025-5 S355J0WP steel plate is kind of atmospheric corrosion resistant hot rolled steel. The atmospheric corrosion resistance of S355J0WP steel in most environments is substantially better than carbon steel with or without copper addition. Corten EN 10025-5 S355J0WP steel plates are weathering steels commonly used for outdoor structures. EN 10025-5 S355J2W steel,S355J2W steel plate,S355J2W S355J2W steel, EN 10025-5 S355J2W steel sheet/Plate, S355J2W improved atmospheric corrosion resistance steel. S355J2W steel is a kind of improved atmospheric corrosion resistance steel. Improved atmospheric corrosion resistance steel means weathering steel or atmosphere corrosion resistance steel. The material No. Of S355J2W is 1.8965
EN 10025 S275 steel properties, composition and equivalent materials can be found in the following datasheet. All data sheet of DIN EN 10025-2 is the same as BS EN 10025-2 and other EU member states. Chemical Composition. Datasheet 1, EN10025 S275J0, S275J2 and S275JR chemical composition based on ladle analysis is given in the following table. EN10025-5 S355J2WP,S355J2WP steel,S355J2WP S355J2WP steel application. Corrosion resistant steel plate S355J2WP under standard EN 10025_5 is mainly used for container steel. Moreover, S355J2WP steel with improved atmospheric corrosion resistance has a wide range of applications:architecture, smokestacks, fabrication,freight wagons, silos, pylons and bridges.
Gangsteel produced and exported EN10025-5 S355K2W steel plate atmospheric corrosion resistance.We sell EN 10025-5 S355K2W weathering resistance steel plate. Adopt Standard:BS EN10025-5 Gangsteel keywords:EN10025-5 S355K2W Equivalent, EN10025-5 S355K2W Composition, EN10025-5 S355K2W Properties, EN10025-5 S355K2W density EN10025-5-S355J2WP - PRIMA DESIGN SteelEN10025-5 S355J2WP Atmosphere Corrosion Resistance Steel. S355J2WP Introduction:S355J2WP steel is a hot rolled structural steel with anti-corrosion feature, also called weathering steel and atmosphere corrosion resistance steel, under standard EN10025-5. EN S355J2WP Chemical Composition
S355 EN 10025 :2004 Standard Structural Steel Plate S355 structural steel plate is a high-strength low-alloy European standard structural steel covering four of the six "Parts" within the EN 10025 2004 standard. With minimum yield of 50,000 KSI, it meets requirements in chemistry and physical properties similar to ASTM A572 / 709. S355J2W+N, S355J2W+N Steel Plate, S355J2W, Corten Steel EN 10025 S355J2W+N Plate Stockists in India, Grade S355J2W+N Corten Plates Exporter, DIN 1.8963 Plates, Corten Steel S355J2W+N Plate Supplier in Mumbai. The qualities that the plates are possessing are guaranteed only by using high quality of alloy and effectiveness in plates production. Those are high tensile strength, sturdy construction
Chemical composition % of steel S355J2WP (1.8946):EN 10025-5-2004. Method of deoxidation FF = fully killed steel For long products the P and S content can be 0.005% higher The steels may show a Ni content of max. 0,65 % Strength Of Steels - Roy MechBS EN 10025-5:2004 - H.r.p.o.s.t. T.d.c. for flat products of high yield strength structural steels in the quenched and tempered condition . These standards are the latest European standards for structural steel. They replace BS 4360, BS EN 10025:1993, BS EN 10113:1993, BS EN 10155:1993 BS EN 10137:1996.
en 10025-5 :sew 087 :nfa 35-502 :bs 4360 :astm:jis g 3114:s235j0w:1.8958-e 24 w 3 -- -s235j2w:1.8961 :wtst 37-3 :e 24 w 4 -- -s355j0wp:1.8945 -e 36 wa 3:wr 50 a - -s355j2wp:1.8946 -e 36 wa 4 -a 242 type 1 - new design en 10025 aisi 1010 steel plate - Carbon steel EN 10025-5 Grade S355J2WP normalized or normalized See where EN 10025-5 Grade S355J2WP normalized or normalized formed (+N) falls on the material property chart for Density against Elastic modulus in your materials selection and design process. Our Ashby charts are interactive with more technical data upon clicking.
Density. . 7.9 - 8.2 g/cm³ at Send us your request for EN 10025-5 Grade S355J2WP normalized or normalized formed (+N) and we will get back to you soon. Ask a technical question Request a quotation. Suggested reading. 440C Stainless Steel:Properties, Processing and Application. AISI 304 (1.4301) Stainless Steel.